List of products by brand Synoxx

The SYNOXX ES-T7-R is a 10GBase-T SFP+ copper transceiver delivering 10Gbps data 
transfers over standard Cat6a or Cat7 twisted-pair cables up to 100 metres — 
eliminating the need for fiber optics in short-to-medium range enterprise and data 
centre deployments. Supports 10G and 1G data rates with a maximum power consumption 
of 2.5W, hot-pluggable SFP+ form factor, and compliance with IEEE 802.3 and SFP+ MSA 
standards. Hot-pluggable, RoHS compliant, and IC Certified for Canada and the US.

The SYNOXX EB232X-10D/EB322X-10D is a matched 25G SFP28 BiDi transceiver pair 
enabling bidirectional 25Gbps transmission over a single strand of single-mode 
fiber (SMF) up to 10km using complementary wavelengths of 1270nm TX/1330nm RX 
and 1330nm TX/1270nm RX. Supports data rates up to 25.78125Gbps with Digital 
Diagnostic Monitoring (DDM), DFB transmitter, APD receiver, and power consumption 
of ≤1.5W per module, compliant with IEEE 802.3cc, SFF-8431, SFF-8432, and 
SFF-8472 standards. Hot-pluggable, RoHS compliant, and IC Certified.

The SYNOXX EDQPY-4SP3 is a 100G QSFP28 to 4×SFP28 passive direct attach copper 
(DAC) breakout cable that splits a single 100G QSFP28 port into four independent 
25G SFP28 connections over 3 metres of twinax copper — enabling cost-effective 
25G server and storage connectivity from a 100G spine or leaf switch port without 
additional transceivers. Compliant with IEEE 802.3bj, SFF-8636, and SFF-8402 
standards, featuring EEPROM support for device identification, low insertion loss, 
and passive operation with no active components required. Hot-pluggable, RoHS 
compliant, and IC Certified.

The SYNOXX EDSP2X-5-26 is a 25G SFP28 to SFP28 passive direct attach copper (DAC)
cable delivering 25.78Gbps over a 5-metre 26AWG twinax connection — built for
extended-rack and end-of-row 25G deployments where 1m and 3m cables fall short,
including cross-rack leaf-to-server links, overhead cable tray runs spanning multiple
rack units, and 100G breakout target connections requiring routing slack across
rack boundaries. Compliant with SFP28 MSA and SFF-8402, featuring a hot-pluggable
SFP28 form factor, fully passive copper with no active components, and operating
temperature range of 0°C to 70°C. Hot-pluggable, RoHS compliant, and IC Certified.

The SYNOXX EDQPY-3 is a 100G QSFP28 to QSFP28 passive direct attach copper (DAC) 
cable delivering 100Gbps over a 3-metre twinax connection using a 4×25G lane 
architecture — purpose-built for cross-rack and adjacent-rack 100G connections where 
1-metre cables fall short. Compliant with SFF-8636 and IEEE 802.3bj, featuring a 
two-wire I2C interface for monitoring and control, low crosstalk design, and power 
consumption under 1.5W per end. Hot-pluggable, RoHS compliant, and IC Certified.

The SYNOXX ES-T5-R-3 is a 10GBase-T SFP+ copper transceiver supporting 
multi-rate 10G/5G/2.5G/1G Ethernet over RJ45, with a 30m reach on Cat 6a/7 
cable. Hot-pluggable, RoHS compliant, and IC certified for Canada and the US.

The SYNOXX EB23X-10D/EB32X-10D is a matched 10G SFP+ BiDi transceiver pair enabling 
bidirectional 10Gbps transmission over a single strand of single-mode fiber up to 10km, 
using complementary wavelengths of 1270nm TX/1330nm RX and 1330nm TX/1270nm RX. 
Supports data rates up to 10Gbps with Digital Diagnostic Monitoring (DDM), DFB 
transmitter, APD receiver, and power consumption of ≤1.5W per module, compliant with 
IEEE 802.3ae and SFP+ MSA standards. Hot-pluggable, RoHS compliant, and IC Certified.

The SYNOXX ESP852X-01D is a 25G SFP28 SR optical transceiver delivering 25.78Gbps 
transmission over multimode fiber — up to 100m on OM4, 70m on OM3, and 20m on OM2 
— using an 850nm VCSEL laser and PIN photodiode, purpose-built for high-density 25G 
Ethernet switching, 5G CPRI fronthaul, and 100G breakout target deployments. 
Features a hot-pluggable SFP28 form factor, LC duplex connector, and Digital 
Diagnostic Monitoring (DDM) via SFF-8472, with low power consumption and compliance 
with IEEE 802.3cc and SFF-8402 standards. Hot-pluggable, RoHS compliant, and IC 
Certified.

The SYNOXX EDQPY-1 is a 100G QSFP28 to QSFP28 passive direct attach copper (DAC) 
cable delivering 100Gbps data transfers over a 1-metre twinax connection using a 
4×25G lane architecture — the ideal same-rack interconnect for 100G spine-leaf 
switching environments. Compliant with SFF-8636 and IEEE 802.3bj, featuring a 
two-wire I2C interface for monitoring and control, low crosstalk, and power 
consumption under 1.5W per end. Hot-pluggable, RoHS compliant, and IC Certified.

The SYNOXX EDSP2X-3 is a 25G SFP28 to SFP28 passive direct attach copper (DAC) 
cable delivering 25.78Gbps over a 3-metre twinax connection — purpose-built for 
adjacent-rack 25G connections where 1-metre cables fall short, including cross-rack 
leaf-to-server links, flexible cable management through overhead trays and 
under-floor pathways, and 100G breakout target deployments with extra slack. 
Compliant with SFP28 MSA, SFF-8402, and IEEE 802.3by, featuring a hot-pluggable 
SFP28 form factor, low power consumption, and a fully passive copper signal path 
with no active components. Hot-pluggable, RoHS compliant, and IC Certified.